Width

Vibration

Vibrations play a large role in the manufacturing industry. There is always vibration where products are in motion. In many cases, this is perceived as an interfering factor and must not exceed specified ...

詳細を表示する

Impact

When an object experiences an impact it is subjected to a specific, directional linear movement. This directional movement is so minute that it can only be detected in the nanometer range. The objects ...

詳細を表示する

カッターディスクのラジアルランナウト測定

高級木材によるベニヤストリップの生産時では、カッターディスクの精度が最終製品の質を決定します。ベニヤストリップには寸法の安定性について高い要求が課され、ストリップの厚さが1 mm ...

詳細を表示する

Underwater measurement of axial movement and shaft play

The functional safety of systems of special economic importance often depends on the perfect operation of delivery devices (pumps). Increased radial shaftwhirl, or an axial shift due to termal expansion, ...

詳細を表示する

Non-contact measurement of relay contact movement

Even the layman can detect wether a relay is energized or not. The question how on the other hand, is difficult to answer even for the expert. What he needs to know is the timing of certain specific parameters ...

詳細を表示する

Monitoring the commutator in electric motors

The “eddyNCDT” system offers many advantages for the non-contact monitoring of the mechanical condition of the commutator in electric D.C. motors or generators. The system uses the eddy-current measuring ...

詳細を表示する

Diameter - radial/axial runout - measurement at disk motors

The production of disk motors has to meet the highest mechanical accuracy requirements. In order to ensure perfect functioning of the disk drives the drive units are measured and evaluated with respect ...

詳細を表示する

Examination of the oscillation behaviour of toothed-belt camshaft drives

To examine the influence of various system and operating parameters on the dynamic behaviour of multi-disk drives a belt oscillation test bench has been set up which simulates the toothed-belt drive system ...

詳細を表示する

路上テストでの振動変位測定

走行装置上での自動車点検は、走行安全性を保証するための前提条件です。このような点検では、路上テストにおける高い要求にも耐えられるセンサが欠かせません。例えば振動変位測定を行う場合、ワイヤ変位センサをショックアブソーバーと平行に取り付け、様々な路面特性でデータを記録し、今ある変位信号をもとに微分により振動速度と振動加速度を算出します。

詳細を表示する

Deformation measurement on lightweight structures

Specially designed measurement systems, which record the surface contours without reactive effects on the lightweight structures, are employed for the examination of component deformations under load. ...

詳細を表示する

Measurement of the radial deviation on superconducting magnets

At the Institute for Solids and Materials Research (IWF) Dresden a motor with magnetic bearings has been developed using high temperature superconductors which can be employed for feed pumps for liquid ...

詳細を表示する

Co-planarity of IC-pins

The term „co-planarity“ discribes the proper seating of the tips of fine-pitch device leads on the copper pads on a PCB prior to solder process. The coplanarity is a critical dimension for the quality ...

詳細を表示する

Automatic inspection and repair of marine propellers

Deformed ship propellers are bent back to their original condition using special machines. Previously, this work was performed manually but today it has been replaced by automatic systems. The current ...

詳細を表示する

Vibration test of wet razor

Modern wet razors provide the function of supporting the shave using vibration. A functional test is performed at the end of production for these models. The razor is switched on and placed in the ...

詳細を表示する
お問い合わせ
Micro-Epsilon Japan K.K.

+81 (0)6 6170 5257

お問い合わせ

Micro-Epsilon Japan K.K.
#1003 Facade Building, 1-23-43, Esaka-cho,
Suita-shi, Osaka 564-0063, Japan
Yukihiro.Makinae@micro-epsilon.jp
+81 (0)6 6170 5257
+81 (0)6 6170 5258