Diameter, Eccentricity, concentricity

コイル直径

金属産業分野では、圧延された金属ストリップ材はコイルに巻いて輸送します。その後の処理時にコイルからストリップ材を解く際、どのくらいの量がすでに巻き戻されたのか必ずわからなければなりません。このタスクは光学レーザーセンサ ...

詳細を表示する

コイルの巻き出し

金属産業分野では、圧延された金属ストリップ材はコイルに巻いて輸送します。その後の処理時にコイルからストリップ材を解く際、どのくらいの量がすでに巻き戻されたのか必ずわからなければなりません。このタスクは光学レーザーセンサ ...

詳細を表示する

Measurement of flat washers

These days, flat washers are an auxiliary material used in almost every industry. In most cases, the washers consist of different alloys and are required in all sizes and thicknesses, which means the demands ...

詳細を表示する

Measurement of metal stampings

Cylindrical, ground stainless steel metal stampings are precisely measured in a fully automatic measurement installation. Two optical optoCONTROL micrometers are applied in order to measure roundness, ...

詳細を表示する

Oscillation

Measuring oscillation is a frequently occurring measuring task. Oscillations occur in research and development, in machines and plant construction as well as production control and are measured using sensors. ...

詳細を表示する

医療用錠剤刻印型と鋳型の品質点検

ISO 18084:2011 によると、医療用錠剤の刻印型は定期的な品質点検を行わなければなりません。刻印型と鋳型は形状が複雑で、表面も強く反射することから、これまで自動での点検は非常に困難でした。しかし、共焦点センサ(confocalDT ...

詳細を表示する

Stainless steel tubes for catalyst production

Various shapes of catalysts require that the stainless steel casing has a precise dimensional stability. For round catalysts, stainless steel tubes are therefore subjected to a diameter check in a special ...

詳細を表示する

Diameter of a pulley

Diameter and concentricity are crucial factors for a long service life, due to the high rotational speeds achieved by pulleys. These parameters are evaluated on a special test bed, using four optoCONTROL ...

詳細を表示する

Non-contacting roundness measurement for rollers

In the production of tapes and foils the high speeds of up to 2700 m/min that are used today lead to an increased vibration tendency in the roller stands. Even smallest μm-range irregularities in the ...

詳細を表示する

管の内径検出

ハウジングのボア測定器 idiamCONTROL は、内径を測定することにより押出し成形機械の8形状ボアの磨耗を検知します。測定プローブをボアの中にスライドさせると、内蔵の静電容量式ダブルセンサが実際のボア直径を測定します。さらにケーブル長さ測定システムがボアの縦軸でセンサの位置を検知するので、センサの位置でどの箇所の直径を検出したのかがわかります。

詳細を表示する

Ovality inspection on brake pipes using vision4A

For the highly accurate measurement of the roundness of the ends of brake pipes in production with short cycle times, only a precise and versatile vision system is able to fulfill the required rapid data ...

詳細を表示する

Bearing shell detection in automotive manufacturing

The presence of the bearing shells is checked automatically for all bearing caps before the assembly of the engines at the Swedish automotive manufacturer, Volvo. The bearing caps are kept in the light ...

詳細を表示する

Drive controller in precision respooling machines

Laser distance sensors from Micro-Epsilon are used for the respooling machines of the MEMA company from Menden. They continuously measure the diameter of coils there. Finished coils for the merging of ...

詳細を表示する

Laser sensors support cable banding

Banding machines are used during the manufacture of cables in order to provide cables with a protective sheath. The wire runs centrally through a roll on which the banding material is coiled. The diameter ...

詳細を表示する

Brake disc concentricity

Brake discs are subject to the highest loads in use and are responsible for the safety of vehicles. For this reason alone, brake discs are thoroughly inspected on test benches. Brake discs are checked ...

詳細を表示する

Roller runout

The runout of the roller is a crucial criterion for rolling processes of metals, plastics or other materials. An imbalance is even dangerous for rollers which have to rotate at high speeds. Therefore, ...

詳細を表示する

Extruder bore diameter

The idiamCONTROL system has been developed for checking the wear of extruder bores. The measuring cylinder is inserted in the case bore and pushed as far as the upper end. During retraction of the cylinder, ...

詳細を表示する

Bore hole depth

It is essential to measure in bore holes for some applications. In doing so, the depth or the wall structure of a bore hole can usually be measured. Only confocal axial or radial miniature sensors with ...

詳細を表示する
お問い合わせ
SENTEC Co. Ltd

+81 6 6304 8858

お問い合わせ

Sankyo International Corp.

+81 3 3662 8100

お問い合わせ

Sankyo International Corp.
No. 9-14, Nihonbashi-Yokoyamacho,
Chuo-Ku, Tokyo 103-0003 Japan
sales@sankyointernational.co.jp
+81 3 3662 8100
+81 3 3662 8050